Web Analytics Made Easy - Statcounter

View Product Gallery

C-Tar Melt

Water Soluble, Non-Hazardous, Powerful Tar Melting Penetration

C-Tar Melt is a blend of water-soluble, non-hazardous ingredients that give exceptionally powerful penetration and softening action. Do not dilute the product with water; product action will be stopped with the application of water. It is biodegradable and will aid in the separation of the tar residue from the rinse water if you contain and store the runoff for a short period of time. The ingredients do not harm the skin, however skin will dry out if constantly exposed to the tar remover.

C-Tar Melt is safe for wood, metal, brick, and masonry surfaces, and will not raise the grain or cause discoloration of the surface on its own. This is a powerful penetrating system, so the best method of tar removal from a painted vehicle is by putting a small amount on a cloth and wiping. Some softening of the paint may occur (that will be stopped upon rinsing), but it is very important to always check the reaction before leaving C-Tar Melt on the surface.

C-Tar Melt Product Spec Sheet

C-Tar Melt Safety Data Sheet

Architectural Spec Sheets

Dilutions:

C-Tar is always used undiluted.

Coverage Rates:

Coverage rates will vary based on dilutions, porosity severity of stain, application method, and other factors. Proper testing will determine actual coverage rate.

Application Instructions:

For tar removal from painted vehicles:
1. Apply C-Tar Melt by putting a small amount on a cloth and wiping
2. Follow proper rinsing procedures

For porous masonry:
1. Spray C-Tar Melt on the surface and allow to dwell for approximately 5 minutes.
2. Typically, two applications will provide better mechanical release than a single application.
3. Number applications and dwell times will vary depending on thickness of the coating to be removed.
4. Follow proper rinsing procedures.

Rinsing:

Proper rinsing techniques determine the final look and quality of the job. A thorough rinse job is always recommended; however, our chemistry never requires flooding a wall.. C-Tar Melt can be rinsed using cold water and low pressure. Pressures that mark the surface should be avoided. When in doubt, follow the manufacturers recommended P.S.I. for the substrates.

Do not use a zero-degree nozzle.

Caution: Do not allow the product to dry on a surface. Keep rinsed off of glass at all times.

Send us your inquiry and we'll get right back to you!

EaCo Chem, Inc. | 765 Commerce Avenue | New Castle, PA | (724) 656-1055 | info@eacochem.com

EaCo Chem

Anodized Aluminum

C-Tar Melt, used undiluted, easily removed the caulk bleed on this aluminum window frame without doing any damage to the glass.

EaCo Chem

Aluminum Equipment

C-Tar Melt easily removed the tar and road grime from this aluminum dump truck bed.

Before and after images of tar being removed from a vehicle battery case

Painted Metal (A)

The battery box on this on this equipment trailer was covered in tar and road grime. C-Tar Melt removed the soiling without damaging the paint.

EaCo Chem

Painted Metal (B)

C-Tar melt was also able to remove the tar and road grime from the fender and wheels as well.

EaCo Chem

Metal and Vinyl

Vaseline was used to keep raccoons from climbing these aluminum downspouts. Black stains appeared over time on the coating. C-Tar Melt was used to restore the downspout to a like-new appearance.

EaCo Chem

Tar on Concrete

The tire from a wheelbarrow spread tar across the concrete in the before photo. You can see in the after photo where C-Tar Melt was used to effectively remove the tar from the concrete area.

EaCo Chem

Tar on Concrete

C-Tar Melt was used to remove these tire marks from pavement.

Add Your Heading Text Here