W.O.W.W

Wash on Wet Wax

Description and Use
W.O.W.W. is a superior wash and wax type product that uses some of the finest new wax technology in a “safe for all surfaces” product. This product will give the extra benefit of good cleaning ability while giving you excellent shine and beading characteristics that lasts for weeks yet never build up or create a haze problem. The clean even extends to such hard to remove problems as tree sap and road oils. W.O.W.W. is an exceptionally mild product with a pleasant odor. It is an excellent choice for a follow up or problem solving solution if soap has hazed an acrylic type wash and wax product. The acrylics often just trap dirt under a water based clear coat that gives shine but not a safe surface for many soaps. You will not have this problem with W.O.W.W. but it may take a few washings to remove the bad acrylic product. W.O.W.W. is very good for the aluminum and chrome surfaces on a car so feel free to use it as a non-abrasive polish.

Advantages
*Safe for all surfaces.
* Doesn’t build up or create haze problem.
*Completely biodegradable.
* Safe for all painted surfaces.

Limitations
*Product effectiveness limited if frozen.

Technical Data
Appearance & Odor: Light amber liquid, mild odor.
Physical State: Liquid
pH: 4.0
Vapor Pressure (mmHg): N/A
Vapor Density (air=1): N/A
Boiling Point: 212° F
Freezing/Melting Point: 20° F
Specific Gravity (WATER =1): 1.140
Evaporation Rate: N/A
Solubility in Water: Complete

Surface & Air Temperatures
Best cleaning results are obtained when air is above 40° Fahrenheit.

Pre-Testing
Always test prior to beginning full-scale cleaning operations. Testing should confirm cleaning effectiveness.

Dilutions
The range of dilutions will run from straight for badly hazed buildups of acrylics, to 30:1 for weekly washing or light duty cleaning.

Application Instructions
W.O.W.W. can be applied by low pressure application by a spray unit or squirt bottle, with a brush or mop, or through a pressure washer. The range of dilutions will run from straight for badly hazed buildups of acrylics, to 30:1 for weekly washing or light duty cleaning. The higher dilutions will give better shine benefits; a little goes a long way. Good washing procedure is to put the product on starting at the bottom and working to the top, and from end to end, with out letting the product dry on the surface. Very little dwell time is needed to get the shine on the surface. Follow this process with a clear water rinse and you will see the immediate beading and benefits of W.O.W.W. Sap and stain removal requires a certain dwell time on the surface and if the product dries you should use it again to reset the finish before rinsing. Dwell times will vary with the surface and the soil, so a trial should always be conducted to ensure the appropriate dilution and dwell time.

Safety Information
Precautionary Measures: Always wear goggles and rubber gloves when handling this product. Keep off of skin and clothing. If material comes in contact with clothing, wash before reuse. Contains Trithhanolamine and d-limonene. Do not get in eyes, on skin or clothing. Avoid breathing fumes. Keep container closed when not in use. Use with adequate ventilation. Applicators should wear rain suit of plastic, rubber or PVC, boots and gloves, face shields and goggles to avoid splash to bare skin or eyes. Dispose of empty containers according to federal, state and local requirements. Do not use for any other applications other than specified. Do not remove label. Read Material Safety Data Sheet for additional safety and health hazard information prior to use.

First Aid +
Instructions in Case of Contact or Exposure Skin & Eye Contact:
Eyes: Flush thoroughly with water for 15 minutes. If irritation persists, seek medical attention.
Skin: Wash off with water. Re-oil skin. If irritation persists, seek medical attention.
Inhalation: Remove to fresh air.
Ingestion: Do not induce vomiting. Drink copious amounts of water. Seek medical attention.

Spill or Leak Procedures
Waste Disposal Method: Check state, local or federal regulations for your area. Steps to be taken if material is released or spilled: wear proper protective equipment while doing cleanup. Large spill: Dike and contain for intended use. Small spill: absorb on oil dry and place in approved container for disposal.

Container Handling/Storage
Keep container closed when not in use. Store the product in containers with Viton seals or silicon sealant gaskets.

Notice
This product has been classified in accordance with the hazard criteria of the CFR.

Disclaimer
The information herein is given in good faith, but no warranty, either expressed or implied is made. Final determination of the suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein we cannot be sure or guarantee these are the only hazards which exist.

Customer Service
Factory personnel are available for assistance at 800-313-8505 and will send you additional information on products as necessary.