Smoke Melt

Alkaline Masonry Cleaner

Description and Use
This is a highly alkaline cleaning product that will remove heavy carbon deposits from metal, wood or masonry at high dilutions. Great care must be taken when applying this product because of its highly active penetrating nature. Smoke Melt will strip latex and enamel paints in a short time. Smoke Melt is good at softening the heavy black smoke from fire damage that occurs on masonry.

Advantages
*Removes heavy carbon deposits.

Limitations
*Will etch windows.

Technical Data
Appearance & Odor: Amber color, mild citric odor
Physical State: Liquid pH: 13.5
Vapor Pressure (mmHg): As Water
Vapor Density (air=1): As Water
Boiling Point: 210°F Freezing/Melting Point: N.A.
Specific Gravity (WATER =1): 1.120
Evaporation Rate: As Water
Solubility in water: Complete.

Preparation Protect:
Test and protect adjacent surfaces from exposure to the cleaning solution.

Surfaces & Air Temperature
To avoid harm to masonry, do not clean when temperatures are below freezing or will be overnight. Best cleaning results are obtained when air and masonry surface temperatures are 40° Fahrenheit or above. If freezing conditions exist prior to application, allow adequate time for masonry to thaw.

Pre-Testing
Always test prior to beginning full-scale cleaning operations. Testing should confirm cleaning effectiveness on each type of surface and stain designated to be cleaned. Test also to determine the desired surface contact time and any potential for adverse reactions with adjacent materials. Allow test panels to dry thoroughly before evaluating final appearance and results.

Dilutions
Cut @ 4:1 up to 9:1 then apply downstream through a pressure washer for severe smoke damage. Cut @ 15:1, then low pressure application for light smoke damage. For brushing application only use product straight up to 10:1. Always complete the cleaning process with a high pressure rinse to remove the product.

Suitable Substrates

Metals, Masonry materials and Wood

Application Instructions
Always protect the surrounding areas by temporarily covering with plastic. If you are spraying this product always try to stay away or above the mist, as it will burn your skin. For black crust removal the product is used straight and left to soak on the surface for 15 minutes to an hour. Pre-wet the area before applying the product and use a nylon brush to apply. Use a high-pressure rinse to remove the product. When removing smoke damage use much higher dilutions but it is still a good idea to give the product lengthy dwell time as Smoke Melt has special additives that cause it to float the soils to the surface. A pressure washer rinse is always needed with this product, preferably in the 1500 to 3000 psi range.

Safety Information Precautionary Measures:
Always wear goggles and rubber gloves when handling this product. Keep off of skin and clothing. If material comes in contact with clothing, wash before reuse. Contains Potassium Hydroxide & Ethanol. Do not get in eyes, on skin or clothing. Avoid breathing vapors. Keep container closed when not in use. Use with adequate ventilation. Applicators should wear plastic, rubber or PVC boots and gloves, face shields and/or goggles to avoid splash to bare skin or eyes. Dispose of empty containers according to federal, state and local requirements. Avoid drifting of material or rinse water onto autos and pedestrians by protecting or diverting such traffic. Do not dilute Smoke Melt with any product except water. Do not use for any other applications other than specified. Do not remove label. Read Material Safety Data Sheet for additional safety and health hazard information prior to use.

First Aid +
Instructions in Case of Contact or Exposure
Eyes: Flush thoroughly with water for 15 minutes. If irritation persists seek medical attention.
Skin: Wash off with soap & water. If irritation persists seek medical attention.
Ingestion: Do not induce vomiting. Drink large amounts of water. Seek medical attention.
Inhalation: Remove to fresh air. If irritation persists, call physician.

Spill or Leak Procedures Waste Disposal Method
Check state, local or federal regulations for your area. Steps to be taken if material is released or spilled: Large spill; dike and contain for intended use. Small spill; absorb on oil dry and place in approved container for disposal.

Container Handling /Storage
Store in a cool dry place. Keep container tightly closed when not in use. Wash thoroughly after handling. Do not use container as dilution or rinsing vessel. Empty containers retain residue and must be handled as if full.

Disclaimer
The information herein is given in good faith, but no warranty, either expressed or implied is made. Final determination of the suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein we cannot be sure or guarantee these are the only hazards, which exist.

Notice
This product has been classified in accordance with the hazard criteria of the CFR.

Customer Service
Factory personnel are available for assistance at 800-313-8505 and will send you additional information on products as necessary.

                                                                                                                                                                                11/04