Showboat

Versatile Truck Wash
Description and Use:
Showboat is a very effective biodegradable wash product is extremely versatile in the ways that can be applied. This product can be applied using low or high pressure and it will work through a foaming arch. High pressure application will give a faster performance and generally higher dilutions. The product will work fine with cold water. High pressure rinse is recommended with Showboat because of the characteristics of this method. Two applications of the soap without rinsing between is the best method to achieve brushless washing. . It is absolutely safe around glass even if it dries on the surface. Showboat does not harm the shine on the surface.

Advantages
*Contains no HF’s.
*Will not etch glass.
*Safe for people, paint and polished aluminum...
*All surface brushless cleaning.
*Biodegradable.
Limitations
*N/A.
Technical Data
Appearance & Odor: Clear viscous liquid, mild odor.
Physical State: Liquid
pH: 10.5
Vapor Pressure (mmHg): N/A
Vapor Density (air= 1) : >1
Boiling Point: 212° F
Freezing/Melting Point: N/A
Specific Gravity (WATER =1): 1.011
Evaporation Rate: <1
Solubility in Water: Complete
Surface & Air Temperatures
Best cleaning results are obtained when air is above 40° Fahrenheit. Do not allow product to freeze.
Pre-Testing
Always test prior to beginning full-scale cleaning operations. Testing should confirm cleaning effectiveness on each type of surface and stain designated to be cleaned.
Dilutions
Down stream directly from concentrate dilute at 20:1 to 50:1 or Pre-dilute at 1:1 (ready to use) first if economy is a top priority then apply a dilution of 10:1 to 20:1 through a pressure washer to achieve desired results.
Application Instructions
This product is best applied through a pressure washer by either low or high pressure. A foaming arch applicator can be used as well. Apply the product with two applications of Showboat without rinsing between is the best method to achieve brushless washing. Allow soaking for several minutes, and then rinse with high pressure. Exceptionally dirty surfaces that have not been washed for along period of time may require a slow application. There is no need to worry about this product on the paint or glass of a vehicle as it will not harm them. It is always recommended though not to let soaps dry on the surface. Refer to the M.S.D.S. for proper safety instructions, but rubber gloves and safety< glasses are always recommended. Product Data and DS PSEPCEIFCICIFAITCIAONTISONS
Safety Information
Precautionary Measures: Always wear goggles and rubber gloves when handling this product. Keep off of skin and clothing. If material comes in contact with clothing, wash before reuse. Do not get in eyes, on skin or clothing. Avoid breathing fumes. Keep container closed when not in use. Use with adequate ventilation. Applicators should wear rain suit of plastic, rubber or PVC, boots and gloves, face shields and goggles to avoid splash to bare skin or eyes. Dispose of empty containers according to federal, state and local requirements. Do not use for any other applications other than specified. Do not remove label. Read Material Safety Data Sheet for additional safety and health hazard information prior to use.

First Aid +
Instructions in Case of Contact or Exposure Skin & Eye Contact:
Eyes: Flood with water for fifteen minutes. If irritation persists, call physician.
Skin: Wash off with soap and water. Irritation persists, seek medical attention.
Inhalation: Remove to fresh air. Ingestion: Drink copious amounts of water. Do not induce vomiting. Seek medical attention.

Spill or Leak Procedures
Waste Disposal Method: Check state, local or federal regulations for your area. Steps to be taken if material is released or spilled: wear proper protective equipment while doing cleanup. Large spill: Dike and contain for intended use. Small spill: absorb on oil dry and place in approved container for disposal.

Container Handling/Storage
Keep container closed when not in use. Do not allow this product to freeze. If spilled on clothing remove and wash before using. Store in containers with Viton seals or silicon sealant gaskets.

Notice
This product has been classified in accordance with the hazard criteria of the CFR.
Disclaimer
The information herein is given in good faith, but no warranty, either expressed or implied is made. Final determination of the suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein we cannot be sure or guarantee these are the only hazards which exist.

Customer Service
Factory personnel are available for assistance at 800-313-8505 and will send you additional information on products
as necessary.
8/12/