HD-Degreaser

Carbon and Grease Remover

Description and Use
A sticky liquid that has excellent adhesion and cleaning ability on vertical and horizontal surfaces. HD will penetrate the most baked on crust due to a very sophisticated combination of aggressive caustics, softening penetrates, and buffering and stabilizing compounds that keep this product from drying out. This allows both fast and long term attack with minimal degradation of surfaces. This dual ability makes HD Degreaser excellent for pre-treating oil stains on concrete. Parking structures and drive through lanes benefit from presoaking the oil stains hours before cleaning as this allows the product time to get deep into the surface and work at lifting out the shadows. This product was originally developed to clean old garbage trucks before repainting and therefore is excellent at soaking through very thick layers of clay, grease, foodstuffs, and hydraulic fluid and oil stains in one application. HD Degreaser will not damage wires or hoses in engine compartments but it may mark the paint.

Advantages
*has excellent adhesion and penetrating cleaning ability on vertical and horizontal surfaces.

Limitations
*it may mark paint

Technical Data
Appearance & Odor: Tan sticky liquid, mild odor.
Physical State: Liquid
pH: 13.5
Vapor Pressure (mmHg): N/A
Vapor Density (air=1): N/A
Boiling Point: 212° F
Freezing/Melting Point: N/A
Specific Gravity (WATER =1): 1.05
Evaporation Rate: N/A
Solubility in Water: Complete

Preparation
*Protection: Test and protect adjacent and surrounding surfaces not intended to be cleaned from exposure to the cleaning solution.

*Surface & Air Temperatures
To avoid harm to masonry, do not clean when temperatures are below freezing or will be overnight. Best cleaning results are obtained when air and masonry surface temperatures are 40° Fahrenheit or above. If freezing conditions exist prior to application, allow adequate time for masonry to thaw.

*Pre-Testing
Always test prior to beginning full-scale cleaning operations. Testing should confirm cleaning effectiveness on each type of surface and stain designated to be cleaned. Test also to determine the desired surface contact time and any potential for adverse reactions with adjacent materials. Allow test panels to dry thoroughly before evaluating final appearance and results.

Dilutions
Apply straight with a brush or low pressure sprayer. If used in a dip tank application this product may be diluted up to 50:1.

Application Instructions
Apply straight with a brush or low pressure sprayer. Oil stains on concrete benefit from a brushing after application. The theory is that this helps drive the degreaser into the pores and lift the shadows. It may also mean that it just increases the dwell time which will benefit any product that does not dry out. If used in a dip tank application this product may be diluted up to 50:1. Allow products to soak until soil is softened. Care should be taken when immersing soft metals such as aluminum in to a hot solution that the metal is not left in the soak for too long. When cleaning badly soiled equipment for repainting it may be best to apply the product with a sprayer one time and then repeat the application in areas that look dry. This usually means that the entire product has been absorbed by the soil and another application will race in through the openings created by the first coat and allow complete release in one rinse. Pressure washer rinsing is best because it will allow complete removal of the stains in the paint.

Coverage Rates
Coverage rates will vary from 100 - 250 sq. ft. /gal depending on the surface porosity, texture and severity of staining.

Safety Information
Precautionary Measures: Always wear goggles and rubber gloves when handling this product. Keep off of skin and clothing. If material comes in contact with clothing, wash before reuse. Contains Sodium Hydroxide. Do not get in eyes, on skin or clothing. Keep container closed when not in use. Use with adequate ventilation. Applicators should wear rain suit of plastic, rubber or PVC, boots and gloves, face shields and goggles to avoid splash to bare skin or eyes. Dispose of empty containers according to federal, state and local requirements. Do not dilute HD Degreaser with any product except water. Do not use for any other applications other than specified. Do not remove label. Read Material Safety Data Sheet for additional safety and health hazard information prior to use.

First Aid +
Instructions in Case of Contact or Exposure Skin & Eye Contact:
Eyes: Flood with water for 15 minutes. Seek immediate medical attention.
Skin: On contact wipe off with a clean cloth, neutralize with vinegar, and then flush with water. If degreaser has had sufficient dwell time to burn skin to redness follow above procedure and call physician.
Inhalation: Remove to fresh air. If irritation persists, call physician.
Ingestion: Drink quart of water, do not induce vomiting. Seek Medical attention

Spill or Leak Procedures
Waste Disposal Method: Check state, local or federal regulations for your area. Steps to be taken if material is released or spilled: Large spill; dike and contain for intended use. Small spill; absorb on oil dry and place in approved container for disposal.

Container Handling/Storage
Store in a cool dry place. Keep container tightly closed when not in use. Do not use pressure to empty container. Wash thoroughly after handling. Do not use container as dilution or rinsing vessel. Empty containers retain residue and must be handled as if full.

Notice
This product has been classified in accordance with the hazard criteria of the CFR.

Disclaimer
The information herein is given in good faith, but no warranty, either expressed or implied is made. Final determination of the suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein we cannot be sure or guarantee these are the only hazards which exist.

Customer Service
Factory personnel are available for assistance at 800-313-8505 and will send you additional information on products as necessary.