C-TAR MELT

Tar Remover

Description and Use
C-Tar Melt is a blend of water soluble non hazardous ingredients that give exceptionally powerful penetration and softening action. This product is not dilutable with water, in fact, its' action will be stopped with the application of water. It is biodegradable and will aid in the separation of the tar residue from the rinse water if you contain and store the runoff for a short period of time. The ingredients do not harm the skin though they will dry it out if left constantly exposed to the tar remover. C-Tar Melt is safe for wood, metal, and masonry surfaces and will not raise the grain or cause discoloration of the surface on its' own. This is a powerful penetrating system, so the best method of tar removal from a painted vehicle is by putting a small amount on a cloth and wiping. Some softening of the paint may occur that will be stopped on rinsing but it is very important to always check the reaction before leaving C-Tar Melt on the surface.

Advantages
*Power penetration and softening action.

Limitations
*Will cause rubber to swell

Technical Data
Appearance & Odor: Water white color characteristic hydrocarbon odor.
Physical State: Liquid
pH: 7.5
Vapor Pressure(mmHg): N/A
Vapor Density (air=1): N/A
Boiling Point: N/A
Freezing/Melting Point: N/A
Specific Gravity (WATER =1): .850
Evaporation Rate: N/A
Solubility in Water: Negligible

Preparation
*Protect:
Test and protect adjacent and surrounding surfaces not intended to be cleaned from exposure to the cleaning solution.

*Surface & Air Temperatures
Best cleaning results are obtained when air and masonry surface temperatures are 40 deg. Fahrenheit or above. If freezing conditions exist prior to application, allow adequate time for masonry to thaw.

*Pre-Testing
Always test prior to beginning full-scale cleaning operations. Testing should confirm cleaning effectiveness on each type of surface and stain designated to be cleaned. Test also to determine the desired surface contact time and any potential for adverse reactions with adjacent materials. Allow test panels to dry thoroughly before evaluating final appearance and results.

Application Instructions
C-Tar Melt is not dilutable and must be used as it comes from the container. As with all solvents proper testing of the material on the surface to be stripped is the only way to determine the correct safe procedure. Basic guide lines would be that the material works better at an ambient temperature in the 70° Fahrenheit range. Proper ventilation should always be a consideration when long term exposure will occur. It is recommended that skin contact be kept to a minimum and at least a water rinse be used after contact. Sometimes two applications one following the other after a short soak period will out perform a single application and mechanical removal. Dwell times will vary with thickness of the coating to be stripped but C-Tar Melt can remove many materials in a fifteen minute time span, heavy layers may be removed with an over night soak. Pressure washer rinsing with at least 1500 psi is recommended for best results.

Coverage Rates
Coverage rates will vary from 100 - 250 sq. ft./gal. depending on the surface porosity, texture and severity of staining.

Safety Information
*Precautionary Measures:
Always wear goggles and gloves when handling this product. Keep off of skin and clothing. If material comes in contact with clothing, wash before reuse. Contains Petroleum Hydrocarbon. Do not get in eyes, on skin or clothing. Avoid breathing fumes. Keep container closed when not in use. Use with adequate ventilation. Applicators should wear boots and gloves, face shields and/or goggles made of solvent resistent materials to avoid splash to bare skin or eyes. Though the potential for fuming of C-TAR MELT is minimal, take precautions to avoid exposing building occupants to fumes. Dispose of empty containers according to federal, state and local requirements. Avoid drifting of material or rinse water onto autos and pedestrians by protecting or diverting such traffic. Do not dilute C-TAR MELT. Do not use for any other applications other than specified. Do not remove label. Read Material Safety Data Sheet for additional safety and health hazard information prior to use.

*First Aid + Instructions in Case of Contact or Exposure Skin & Eye Contact:
Eyes: Flood with water 15 minutes. Seek immediate medical attention.
Skin: Wash off with soap and water. If irritation persists, call physician.
Inhalation: Drink lots of water. Seek immediate medical attention.
Ingestion: Remove to fresh air. If irritation persists, call physician.

Spill or Leak Procedures
Waste Disposal Method: Check state, local or federal regulations for your area. Steps to be taken if material is released or spilled: Large spill; dike and contain for intended use. Small spill; absorb on oil dry and place in approved container for disposal.

Container Handling/Storage
Store in a cool dry place. Vent bung before opening. Keep container tightly closed when not in use. Do not use pressure to empty container. Wash thoroughly after handling. Do not use container as dilution or rinsing vessel. Do not cut, grind or weld on or near container. Empty containers retain residue and vapors and must be handled as if full.

Notice
This product has been classified in accordance with the hazard criteria of the CFR.

Disclaimer
The information herein is given in good faith, but no warranty , either expressed or implied is made. Final determination of the suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein we cannot be sure or guarantee these are the only hazards which exist.

Customer Service
Factory personnel are available for assistance at 800-313-8505 and will send you additional information on products as necessary.