Concrete Truck Cleaner

Concrete Remover

Description and Use:
Concrete Truck Cleaner is specifically made for removal of build-up concrete on trucks. This product may require extended dwell times for the heaviest build-up. Also can be used as a concrete brightener and stain remover.

Advantages:
*Power penetration and softening action.

Limitations:
*May burn if used repeatedly straight.

Technical Data:
Appearance & Odor: Clear liquid, mild biting odor.
Physical State: Liquid
pH: 1.0
Vapor Pressure(mmHg): As water
Vapor Density (air=1): As water
Boiling Point: 210° F
Freezing/Melting Point: NA
Specific Gravity (WATER =1): 1.15
Evaporation Rate: As water
Solubility in Water: Complete

Preparation:
Test and protect adjacent and surrounding surfaces not intended to be cleaned from exposure to the cleaning solution.

*Surface & Air Temperatures:
Best cleaning results are obtained when air temperatures are 40° Fahrenheit or above.

*Pre-Testing:
Always test prior to beginning full-scale cleaning operations. Testing should confirm cleaning effectiveness on each type of surface and stain designated to be cleaned. Test also to determine the desired surface contact time and any potential for adverse reactions with adjacent materials. Allow test panels to dry thoroughly before evaluating final appearance and results.

Dilutions:
2:1 up to 5:1 dilution is the best application range. There is danger of burning the surface if the product is used repeatedly straight.
10:1 or 20:1 (12 oz. or 6 oz. per gallon) low pressure application for concrete brightening.
5:1 or 10:1 for stain removal from concrete. If your test patch indicates the need to use the product straight (undiluted), it is recommended to use an alkaline presoak that can be applied hours or days in advance.

Application Instructions:
Apply Concrete Truck Cleaner with a sprayer or conventional brushing to surfaces to be cleaned. Allow 5 -10 minutes contact time. Apply again, let stand for another 5-10 minutes then pressure rinse off thoroughly.  Heavy build-up on neglected or unassigned trucks, repeat the process daily for several days until all build-up is removed. Concrete Truck Cleaner should not be used on the cabs of trucks as a regular truck cleaner, but may be used on occasion to remove cement dust and splatter. Rinse completely.

Safety Information
*Precautionary Measures:
Always wear goggles and rubber gloves when handling this product. Keep off of skin and clothing. If material comes in contact with clothing, wash before re-use.  Contains Hydrochloric Acid. Do not dilute Concrete Truck Cleaner with any other product except water. Do not use for any other applications other than specified. Do not remove label.  Read Material Safety Data Sheet for additional safety and health hazard information prior to use.  Do not get in eyes, on skin or clothing. Avoid breathing fumes. Keep container closed when not in use. Use with adequate ventilation. Applicators should wear rain suit of plastic, rubber or PVC, boots and gloves, face shields and/or goggles to avoid splash to bare skin or eyes. Use a MIOSH/MSHA approved respiration for use with acids if adequate ventilation is unavailable. Though the potential for fuming from Concrete Truck Cleaner is minimal, take precautions to avoid exposing building occupants to fumes. Dispose of empty containers according to federal, state, and local requirements. Avoid drifting of material or rinse water onto autos and pedestrians by protecting or diverting such traffic.

*First Aid +
Instructions in Case of Contact or Exposure Skin & Eye Contact:
Eyes: Flood with water 15 minutes. Seek immediate medical attention.
Skin: Wash off with soap and water. If irritation persists, call physician.
Inhalation: Remove to fresh air. If irritation persists, call physician.
Ingestion: Drink lots of water. Seek immediate medical attention.

Spill or Leak Procedures:
Waste Disposal Method: Check state, local or federal regulations for your area. Steps to be taken if material is released or spilled: Large spill; dike and contain for intended use. Small spill; absorb on oil dry and place in approved container for disposal.

Container Handling/Storage:
Store in a cool dry place. Vent bung before opening. Keep container tightly closed when not in use. Do not use pressure to empty container. Wash thoroughly after handling. Do not use container as dilution or rinsing vessel. Do not cut, grind or weld on or near container. Empty containers retain residue and vapors and must be handled as if full.

Notice:
This product has been classified in accordance with the hazard criteria of the CFR.

Disclaimer:
The information herein is given in good faith, but no warranty, either expressed or implied is made. Final determination of the suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein we cannot be sure or guarantee these are the only hazards which exist.

Customer Service:
Factory personnel are available for assistance at 800-313-8505 and will send you additional information on products as necessary.